Chassis Parts

Our Stainless Steel Brake Stay kit is an adjustable link containing stainless heim joints at either end to allow for high strength as well as correction of misalignment of the two mounting surfaces. Every part of the link and hardware is made of...

These parts are great for making lower controls sprung seat piviots and anything else that needs to pivot or rotate freely without premature wear on your hardware.  These are mild steel fittings with a bronze bushing already pressed into place...

Our Stainless Steel Brake Stay kit is an adjustable link containing stainless heim joints at either end to allow for high strength as well as correction of misalignment of the two mounting surfaces. Every part of the link and hardware is made of...

Spring Seat Front Piviot Our front pivot contains stainless shoulder bolts for a snug fit and bronze oilite bushings for trouble free operation. When used properly, these pivots remove most side to side play found in some sprung seats. This is a weld on...

Straight Motor Mount Kit This kit includes all the materials needed to create a custom motor mount for V-twim motorcycles. To create your new motor mount is bolt the 3" bullet to your chassis tab, then install the supplied counterbore bungs into your...

This mount is for those of you not using the standard forward controls on softails, early rigid, and aftermarket frames, but would like to run the factory bolt-on kickstand. From the factory, the only way they leave you to bolt on your kickstand is...

Curved Motor Mount Kit This kit includes all the materials needed to create a custom motor mount for V-twim motorcycles. Made for SAE head bolt sizes 3/8" (evo and TC) and 7/16" (Pan,Shovel and Ironhead). Each kit contains: two counterbored bungs of the...

3/4" ID Wheel Spacer Stock This product is for those of you who like to make your own wheel spacers but would like to save yourself some time. This stock comes in 6" sections, the ID is reamed to .752" so it will slip smoothly over your 3/4 axle and has...

This is our Jockey shift motor mount kit, it is designed for those looking to make a motor mount with an integral pivot for a jockey shift handle. They are available for all Harley motor types. You bolt the center pin that is tapped to accept a 1/2 x 13...

Frame Tubing Caps   Full half domes Made from 10ga mild steel Used to clean up tubing ends available in either 1", 1 1/4", or 1 1/2" O.D. All are weld in style Sold Each  

If you are running extra tall shocks or front forks, your bike may experience an excessive angle when leaned over on the kickstand. Our kickstand lift block can help eliminate this issue. It bolts directly to the bottom of your kickstand with the...

If you are running extra tall shocks or front forks, your bike may experience an excessive angle when leaned over on the kickstand. Our kickstand lift block can help eliminate this issue. It bolts directly to the bottom of your kickstand with the...

If you are running extra tall shocks or front forks, your bike may experience an excessive angle when leaned over on the kickstand. Our kickstand lift block can help eliminate this issue. It bolts directly to the bottom of your kickstand with the...

This is a 1/4" thick mounting tab to hold up to those harsh applications. It is made of 1/4" thick mild steel to reduce bending or distorting under load like the stamped steel ones that are made of 1/8" or thinner that are on the market. We have used...

  Here’s an SEO-optimized product description for your Swingarm Lift Kit: Swingarm Lift Kit for Dyna & Sportster – Improve Ground Clearance & Cornering Performance Looking to enhance your cornering performance and...

Kickstand Lift Block for Taller Shocks & Front Forks – Improve Bike Stability If you're running extra tall shocks or front forks on your bike, you may have noticed an excessive lean when it's on the kickstand. The Kickstand Lift Block is the...

Brake Stay Tab   Weld on tab for your rear brake stay and other uses Made from 3/16" thick mild steel 3/8" or 1/2" Diameter hole CNC cut Sold Each  

Brake Stay Tab With Lightening Holes • Weld on tab for your rear brake stay and other uses • Made from 3/16" thick mild steel • 3/8 Diameter hole • Two 1/2" lightening holes • CNC cut • Sold Each for $6.00